Why Your Dryer Stops Mid-Cycle & How to Fix It

By Fix4U Team
Dryer, Laundry Appliances

You load up the dryer, start a cycle, and come back later only to find damp clothes and the dryer sitting idle. Partial cycles that don’t complete are super annoying. But don’t worry – a dryer stopping mid-run is usually caused by just a few component failures that can be quickly identified and repaired.

This dryer troubleshooting guide from Fix4U Repairs will cover the common causes of dryers quitting partway through a cycle and how to get yours running fully again.

What Makes a Dryer Stop Mid-Cycle?

When a dryer stops before the cycle finishes, these are the most common culprits:

Defective Door Switch

If the door switch fails to activate when the door is closed, the dryer thinks it’s open and stops the cycle.

Bad Start/Stop Button

If the push button stops working, pressing it won’t restart a stopped dryer. The button requires replacement.

Faulty Timer

The timer controls cycle progression. If it sticks, shuts off early, or fails to advance, the full cycle won’t complete.

Tripped Thermal Fuse

If the dryer overheats, the thermal fuse will trip and shut off power to stop the dryer.

Blown Thermistors

Thermistors monitor dryer temp. If readings go off, it can interrupt the cycle before finishing.

Obstructed Venting

A partially blocked vent or lint trap restricts airflow which can cause overheating and sudden shut down.

Diagnosing Mid-Cycle Dryer Stopping

Fix4U Repairs' Technicians Fixing Dryer Mid Cycle Stop Problem In Gta

Start basic dryer troubleshooting with these steps:

  • Check if the door stays latched when the unit is running. Listen for clicks when closed.
  • Examine the start/stop button for damage. Test button manually for continuity and function.
  • Inspect timer contacts while manually advancing the cycle dial.
  • Clean lint trap and use a vent brush to clear any visible vent clog.
  • Check thermistors and thermal fuse for visible breakage and test continuity.
  • If restarting works temporarily, assess for overheating issues.

How to Repair a Dryer That Stops Mid-Cycle

Once the specific cause is pinpointed, common fixes include:

Replace Door Switch

  1. Unplug the dryer and disconnect two door switch wires.
  2. Remove mounting screws and install new door switches.
  3. Reattach wires to proper terminals.

Replace Push Button

  1. Access button by opening control console panel.
  2. Detach wires from faulty push buttons and remove any screws.
  3. Connect wires to the replacement button and install it in place.

Replace Timer

  1. Unplug the dryer and open the console panel to access the timer.
  2. Disconnect the wiring harness and remove any fasteners.
  3. Install new timer motor assembly and reconnect wires. Test operation.

Clear Vent Obstruction

  1. Disconnect vent duct and use duct brush to dislodge lint and debris clogs.
  2. Vacuum duct completely. Reattach the duct to the dryer vent tightly.

End mid-cycle dryer interruptions. Call Now to Fix Your Dryer!

Preventing Mid-Cycle Dryer Shutdowns

Routine preventive maintenance goes a long way:

  • Clean lint traps thoroughly before every cycle to maintain airflow.
  • Detach and clean vent ducts yearly to prevent blockages.
  • Confirm the vent duct meets length limits and isn’t kinked or restricted.
  • Make sure the dryer is properly leveled so the door shuts completely.

When you need a dryer you can rely on, the pros at Fix4U Repairs will get to the root cause of any mid-cycle stopping problem and have you back to full, uninterrupted cycles. Contact us at (647) 363-5205!

(647) 363-5205

Fix It with Fix4U Today!
Get A Free Quote Now!

BLOGS

Our latest articles

Fix4U Team
Dishwasher, Kitchen Appliances

Dishwasher Not Draining Properly

Read More
Fix4U Team
Dishwasher, Kitchen Appliances

Dishwasher is Leaking

Read More
Fix4U Team
Dishwasher, Kitchen Appliances

Dishes Come Out Dirty

Read More