Why Your Washer Stops Mid-Cycle and How to Fix It

By Fix4U Team
Washing Machine, Laundry Appliances

It can be incredibly frustrating when you start a load of laundry, only to have your washing machine suddenly stop mid-cycle. The soap and water are still sloshing around, the clothes are sitting there sopping wet…and now you’re left wondering what’s wrong with the washer.

Stopping abruptly in the middle of the wash cycle is a common problem with washing machines. But don’t worry – in most cases, it’s an issue that can be resolved with some basic troubleshooting and minor repairs.

In this article, we’ll walk through the most common reasons a washer stops mid-cycle and show you how to get your appliance back up and running.

Common Causes For a Washer Stopping Mid-Cycle

There are a handful of typical culprits behind washers that quit prematurely:

Fix4U Repairs' Technicians Fixing Washer Stops Mid-Cycle Problem In Gta
  • Power supply issues
  • Water inlet valve failure
  • Broken lid switch
  • Faulty timer
  • Pump/motor failure
  • Thermostat problems
  • Heating element failure

Below, we’ll explore each of these common mid-cycle stopping points in greater detail and provide tips for diagnosing washer problems.

Power Supply Issues

The most obvious reason your washer stops mid-cycle is because the power supply gets interrupted.

If your home experiences a power outage, your washing machine will shut off along with other appliances. It remains paused in the cycle until electricity returns.

You’ll also want to check for issues with the power supply to the washer itself. Problems with the electrical outlet, wiring, breaker, or plug can prevent the washer from getting consistent power.

Start troubleshooting power supply issues by unplugging the washer and plugging it into a different outlet. This will tell you if the issue is with the outlet versus within the appliance itself.

Inspect the power cord as well for damage. Fraying, exposed wires, and cracks are easy to spot. You may simply need to replace the cord.

Test the outlet with another appliance like a lamp or phone charger. If other devices work, the problem lies with the washer plug itself. Try replacing just the plug before replacing the whole power cord.

Lastly, check your home’s breaker box to make sure the breaker controlling the washer is switched fully on.

Water Inlet Valve Failure

Washing machines have electric water inlet valves that control the flow of hot and cold water into the machine. If either valve fails, it will prevent water from entering the wash tub during the fill cycle.

The washer will pause, waiting for water intake that never arrives due to the faulty inlet valve. It then stops mid-cycle once it hits the preset timeout limit.

You can test the water inlet valves using a multimeter. Set the multimeter to test for continuity and touch the probe pins to the valve wire terminals.

If the reading shows no continuity, the valve is defective. The resistance should be very low, no more than a few ohms.

Replacing the water inlet valve yourself is straightforward – just turn off water supply lines, disconnect hoses, remove screws, and swap in the new valve. Consult your owner’s manual for the proper part number.

Broken Lid Switch

There is a small lid switch located right near the washer lid latch assembly. This switch is what senses when the washer lid is closed and signals to the machine that it’s okay to start operating.

If this switch fails, the washer believes the lid is still open, even when you’ve closed it completely. It will not progress through the cycles.

Start diagnosing a lid switch issue by opening the washer lid and inspecting the switch visually. Look for any broken or loose parts and check that the switch plunger gets depressed when you close the lid.

Use a multimeter to test for continuity with the lid closed and open. You should only have continuity when the lid is shut and the plunger is pushed in.

If the switch tests faulty, locating and replacing the lid switch is a quick 5-minute fix in most models. Just be sure you get the correct replacement part.

Faulty Timer

Washing machines have electromechanical timers or electronic control boards that control the cycle progression. The timer signals when it’s time to advance to the next cycle, like from wash to rinse.

If the mechanical timer is defective, the washer may get stuck doing the same cycle repeatedly or just stop mid-cycle. The timer is not sending the signal to progress even though the cycle should be finished.

Electronic control boards can fail in similar ways. The washer gets confused about what point it’s at in the cycle and stops prematurely or repeats portions of the cycle.

Diagnosing timer issues can be tricky without a wiring diagram. You may be able to spot loose or damaged connections on an electromechanical timer. Replacement is the fix for both mechanical and electronic timers.

Pump or Motor Failure

The pump in your washer plays a crucial role, draining water from the wash tub at key points in the cycle.

Likewise, the motor drives the drum to agitate clothes during washing. If either component fails, the washer may stop mid-cycle once it can no longer adequately pump or spin.

Check first for obstructions like coins, socks, or debris clogging the pump. If the pump seems clear, use a multimeter to test the motor windings for continuity. The pump may need to be replaced if faulty.

Worn bearings in the motor can also cause enough friction to impede drum spinning. Have a technician diagnose and replace the motor if needed.

Thermostat Issues

Many washers feature a thermostat that controls internal heating during cycles. If it malfunctions, the washer may not reach the target temperature needed to advance the cycle.

Some washers stop mid-cycle once they detect the temperature is not rising as expected. The thermostat may simply be tripped and need resetting. If it’s defective, a new thermostat restores normal operation.

Heating Element Failure

In addition to the thermostat, heating elements heat the water for washing and rinsing. Burned out or broken heating elements prevent the washer from properly warming the water to complete a cycle.

Visual inspection of the element wiring and housing provides good clues. Damage like cracks or disconnected wires indicate it’s time to replace the heating element.

Multimeter resistance tests help too. The element resistance should match manufacturer specs when checked offline. Significant variance indicates a faulty element.

Step-by-Step Diagnosis and Repair Process

Now that you know the most common reasons washers stop mid-cycle, let’s walk through a streamlined troubleshooting process. Follow these steps to successfully diagnose and fix your washing machine:

1. Check Power Supply

Start by verifying power is reaching the washer properly:

  • Plug washer into different outlet
  • Check power cord and plug for damage
  • Test outlet functionality with another appliance
  • Ensure breaker is switched fully on

Restore power if there is an interruption found. Replace damaged cords, plugs, or outlet wiring as needed.

2. Check Water Supply

Faulty water valves prevent proper fill:

  • Turn off hot/cold supply lines and inspect fill hoses
  • Use multimeter to test inlet valve resistance
  • Replace valve if resistance is too high

Clear any kinks or clogs found in the supply hoses. Install new hoses if wear is detected.

3. Check Lid Switch

A broken lid switch prevents cycle progression:

  • Inspect switch visually for damage
  • Test with multimeter for continuity (closed vs open)
  • Replace lid switch if not signaling properly

4. Advance Timer Manually

See if the washer will proceed if you advance the timer:

  • Locate timer knob or electronic control
  • Slowly advance timer into next cycle position
  • Listen/look for proper cycle resumption

If washer still won’t proceed, suspect control board or timer motor issues.

5. Check Pump and Motor

Pump or motor failures affect spin cycles:

  • Ensure pump inlet/outlet are clear of debris
  • Check motor windings with multimeter
  • Replace pump or motor if defective

6. Check Heating System

Faulty heating prevents temperature rise:

  • Examine heating element for damage
  • Use multimeter to check element resistance
  • Test thermostat continuity across terminals
  • Replace element or thermostat if faulty

7. Reset Washer and Retest

After making any repairs, unplug the washer, wait 1 minute, plug back in, and retest a full cycle. Monitor carefully to see if the issue recurs or is now resolved. Additional troubleshooting may be needed if the washer continues stopping mid-cycle.

Washer stops mid-cycle? Call Now To Fix Your Washer !

When to Call for Washer Repair Assistance

With some basic diagnostic steps and component testing, you can troubleshoot a surprising number of mid-cycle stopping issues on your own.

However, if you still can’t get your washer running properly after working through the checklist, don’t hesitate to call in a professional.

Washer repair technicians have specialized training, expertise, and tools to accurately pinpoint problems. They can perform in-depth testing and repairs beyond what’s feasible for DIY maintenance.

The pros can also completely disassemble washers down to the cabinet to rectify problems. With experience from repairing hundreds of washers, technicians have seen all the problems possible.

Don’t let frustration build trying to fix it yourself. Calling Fix4U Repairs in the GTA when your washer stops mid-cycle ensures proper diagnosis and repair from washer experts.

Cost to Repair a Washer Stopping Mid-Cycle

When it comes time for professional washer repair, costs depend on a few key factors:

  • Type of repair needed – Simple fixes like replacing a lid switch cost less than major motor or control board repairs. Expect to pay more for extensive repairs.
  • Washer brand – Replacement parts and complexity of repair will vary across brands. Complex, computerized washers tend to cost more.
  • Labor time – The hourly rate for washer repair techs multiplied by the time a repair takes impacts overall cost. Quick fixes take less time.
  • Location – Repair rates can vary regionally based on labor costs and local rates set by companies. Expect some geographic variability.

While it’s hard to give an exact price without diagnosing the specific issue, expect to budget $200-$400 for professional washer repair to get the appliance running again.

Complicated repairs with lots of labor time or control board programming can sometimes reach $600-$800 for more involved jobs. But the majority of mid-cycle stopping issues fall in the lower range.

Replacing the whole washing machine is almost always more expensive than repairing a stopping issue. With proper diagnosis and service, repair extends the useful life of your appliance at a fraction of replacement cost.

DIY Troubleshooting Tips to Keep Your Washer Running

While some washer repairs like control board replacement are best left to professionals, there are minor troubleshooting steps you can take yourself between service calls.

Follow this simple checklist to keep your washer running smoothly:

Clean the water inlet filters – Sediment buildup in the hot and cold inlet filters can impede proper water flow into the tub. Periodically clean out these screens.

Inspect the water pump filter – Check the pump filter for stuck items that could clog the drainage system. Remove coins, buttons, debris to prevent mid-cycle drain issues.

Clean the lid switch – Gently wipe down the plunger and contacts of the lid switch to prevent sticking or corrosion issues that could stop operation.

Leave the lid open – Whenever not in use, leave the washer lid open to allow interior drying and prevent mildew buildup. A soggy washing machine can lead to foul odors.

Level the washer properly – Use an adjustable wrench to turn the leveling feet under the washer to ensure it sits evenly balanced without rocking. Improper leveling causes vibrations and noise.

Tighten hose connections – Check that the water inlet and drain hoses are tightened securely to prevent leaks and water pressure issues during filling.

Prevent overload – Never stuff too many clothes into the drum. Overloading puts strain on the motor and bearings leading to premature wear.

Staying on top of basic user maintenance keeps your washer running smoothly for years before repairs are needed. But when problems do pop up, trust the experts at Fix4U Repairs to diagnose and fix your washer professionally so you can keep your home running cleanly.

When to Buy a New Washer

Reaching the point when fixing your washer no longer makes sense due to the repair costs or frequency can be frustrating. But when the expense of fixing continuous mid-cycle issues exceeds the cost of buying a new machine, purchasing a replacement washer is the smart option.

Here are a few signs it’s time to replace rather than repair:

  • Frequent breakdowns and repairs needed
  • Difficulty finding replacement parts due to unit age
  • Cost of repairs is more than 50% of new washer price
  • Energy usage is high compared to newer models
  • Desired features are now outdated

New washers have improved technology, efficiency, capacity, and features. Once the repair hassle outweighs the cost to upgrade, buying new makes sense.

Finding the Best Washer for Your Needs

If purchasing a new washing machine, keep these key factors in mind as you shop and compare models:

  • Capacity – Match tub size to your household laundry demands. Calculate for future needs too.
  • Efficiency – Look for ENERGY STAR models. Front loaders tend to be most water and energy efficient.
  • Controls – Digital controls with cycle customization options provide convenience.
  • Noise – Check decibel ratings and user reviews. Quieter machines have improved sound dampening.
  • Reliability – Read reliability ratings and warranties to gauge longevity and durability.

Focusing on the features that matter most to your lifestyle helps you select the ideal washer. Trusted brands known for reliability are smart buys.

(647) 363-5205

Fix It with Fix4U Today!
Get A Free Quote Now!

BLOGS

Our latest articles

Fix4U Team
Dishwasher, Kitchen Appliances

Dishwasher Not Draining Properly

Read More
Fix4U Team
Dishwasher, Kitchen Appliances

Dishwasher is Leaking

Read More
Fix4U Team
Dishwasher, Kitchen Appliances

Dishes Come Out Dirty

Read More