Why Your Washing Machine Won’t Finish Its Cycle & How to Fix It

By Fix4U Team
Washing Machine, Laundry Appliances

You load a pile of dirty clothes into your washer, start the cycle, then come back later only to find wet clothes still sloshing around in unfinished cycles. It’s incredibly frustrating when your washer fails to automatically advance and complete all the proper cleaning stages.

There are several possible causes for washers getting stuck mid-cycle ranging from faulty timers to blocked pumps. By methodically troubleshooting the different components, you can zero in on the root cause and get your washer cycling properly again.

In this guide, we’ll cover the key reasons washers fail to finish cycles and step-by-step fixes to get your laundry back on track.

Common Causes of Incomplete Washer Cycles

When your washing machine fails to automatically advance through the programmed stages of a wash cycle, the root causes often include:

  • Defective timer – The timer controls cycle progression. If it malfunctions, the washer may get stuck at one stage.
  • Faulty water level switch – This determines the right water level. If broken, the washer may never fill sufficiently to proceed.
  • Blocked or failed water valves – Issues with the hot and cold water intake valves can prevent proper water supply.
  • Clogged or frozen hoses – Kinked and obstructed water hoses keep the unit from filling correctly.
  • Broken motor coupler – This connects the motor to drive train. If defective, drive mechanics can’t advance the cycle.
  • Failed motor controller – The controller manages motor operation. If it malfunctions, stages can’t progress.
  • Drain pump problems – A clogged or jammed drain pump prevents proper water removal.
  • Defective lid switch – The lid switch ensures door is safely shut. If faulty, washer may not start or pause mid-cycle.

Troubleshooting Cycle Progression Issues

When your washer is stuck at one stage and won’t complete all cycle steps, methodically test each component that manages cycle automation:

  • 1. Check that all electrical connections are secure: Inspect the power cord, outlet, and control panel connections to ensure a faulty connection is not interrupting electrical supply.
  • 2. Verify proper water supply: Ensure hot and cold supply valves are fully turned on. Check that inlet hoses are not kinked or clogged. Make sure home water pressure is adequate.
  • 3. Test the water level switch: The pressure switch should click as water fills to certain levels. Replace if no clicks are heard.
  • 4. Inspect water inlet valves: Remove fill hoses and inspect valves for blockages. Test power to valves. Replace faulty valves.
  • 5. Check the timer: Advance the timer dial through the cycle stages manually to isolate issues. Replace defective mechanical or electronic timers.
  • 6. Test the motor coupler
  • The coupler should have no play when rotating by hand. Replace worn or damaged couplers.
  • 7. Evaluate drain pump operation: Power off, disconnect hoses and ensure no blockages. Check pump volts. Replace failed pumps.
  • 8. Examine lid lock/switch: Test with multimeter and replace if no continuity. Adjust or replace faulty latch assemblies.
  • 9. Replace controller boards: For washers with electronic sensors and controls, circuit board failures can prevent cycle operation.

Causes of Specific Mid-Cycle Stoppages

In addition to testing components, take note of exactly what point in the cycle the washer is stopping:

  • Won’t fill – Generally indicates water inlet valve issues or insufficient water supply.
  • Won’t agitate – Typically points to motor coupler, drive belt or control problems.
  • Won’t spin – Usually signals motor, pump or lid switch defects.
  • Won’t drain – Clogged or jammed drain pumps are the most common cause.
  • Stops mid cycle – Often caused by defective timers, lid latches or control boards.

Getting Your Washer Cycling Properly Again

Once you’ve diagnosed the specific component causing the cycle progression failure, you can take steps to get your washer functioning normally again:

  • Replace worn or defective timers and motors.
  • Clear any clogs or obstructions from pumps and hoses.
  • Swap out broken water inlet valves, pressure switches and sensors.
  • Repair or change out faulty control boards or motor couplers.
  • Ensure latches close securely to properly engage lid switches.
  • Verify stable electrical connections with no shorts or disconnected wires.

With the component repaired or replaced, run the washer through a full cycle to confirm it advances automatically through all stages again.

Preventive Maintenance to Avoid Cycle Issues

You can minimize mid-cycle stoppages through periodic washer maintenance:

  • Clean the filter monthly to prevent drain pump clogs.
  • Inspect inlet hoses annually and replace any bulging or cracked hoses.
  • Wipe door seals with bleach monthly to prevent mildew buildup.
  • Ensure washer is properly leveled to avoid leaks.
  • Run cleaning cycles monthly to flush out any debris in lines.
  • Test components like timers for smooth operation when servicing.

With regular maintenance and inspection, small issues can be caught early before interrupting cycles.

Washer quits early? Call Now To Fix Your Washer !

When to Call a Washing Machine Repair Technician

For homeowners less comfortable with electrical and mechanical repair, contact a professional washing machine repair company when your washer fails to complete cycles.

Technicians like Fix4U Repairs have specialized tools to diagnose issues and perform repairs like:

  • Testing pressure switches, valves and motor windings
  • Replacing control boards and cycle timers
  • Removing stuck item from drains/pumps
  • Adjusting and realigning drive components
  • Identifying leaks in hoses and water supply lines

We can quickly get your washer cycling properly again. Call (647) 363-5205 for expert washer cycle repairs.

The Cost of Letting Cycle Problems Go

It’s frustrating having to restart wash loads multiple times. But incomplete cycles can also lead to higher water and energy costs.

More importantly, letting broken components go unrepaired often leads to more extensive damage like flooded laundry rooms from unchecked leaks or electrical hazards.

Getting any mid-cycle stoppage issues properly diagnosed and fixed provides reliability and prevents further breakdowns.

Key Takeaways

  • Washers that won’t automatically finish cycles are very common. Issues from control boards to lid switches could be the culprit.
  • Note exactly what point in the cycle the washer stops to isolate the faulty component.
  • Methodically testing parts like timers and inlet valves can identify the problem.
  • Make simple repairs like drain pump cleaning yourself. More complex repairs are best left to appliance pros.
  • With the faulty component replaced, your washer should resume completing full uninterrupted cycles.
(647) 363-5205

Fix It with Fix4U Today!
Get A Free Quote Now!

BLOGS

Our latest articles

Fix4U Team
Dishwasher, Kitchen Appliances

Dishwasher Not Draining Properly

Read More
Fix4U Team
Dishwasher, Kitchen Appliances

Dishwasher is Leaking

Read More
Fix4U Team
Dishwasher, Kitchen Appliances

Dishes Come Out Dirty

Read More